Will the Dexter 6K Disc Brake Kit for Nev-R-Lube Axles Work On a Dexter D52 Nev-R-Lube Axle

Question

Question:

Would these kits work on my 2016 Arctic Fox 29-5t with a Dexter d52 never lube axle

asked by: Don H

1

Helpful Expert Reply:

The Dexter D52 Nev-R-Lube Axle uses 42mm bearing cartridges according to my research so the Dexter Disc Brake Kit part # K71-647-648 will fit just fine.

expert reply by: Conner L

1

Answer 1

Your Dexter D52 axles should be rated at 5,200 lbs and use 12 inch brake assemblies. Going with a 6k rated brake assembly would be your best choice since they do not offer a 12 inch brake assembly with a 5,200 lb capacity. For that I would recommend…

view full answer...

Answer 2

Yes, the Grease Seal - Double Lip #GS-2250DL that you referenced would be the correct replacement seal for your Dexter 5,200 lb axle on your 2013 Open Range 5th Wheel.

view full answer...

Answer 3

The brake assemblies you have are 7k Dexter assemblies that are 12 inch by 2 inch in size. The part number #AKEBRK-7-SA will work as a great replacement set. This includes assemblies for both sides of your trailer that are self adjusting.

view full answer...

Answer 4

Since you said your current EZ Flex Equalizers are 7-3/4 inches from bolt hole center to bolt hole center the correct replacements you'd need is the part #K71-655-00.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Will the Dexter 6K Disc Brake Kit for Nev-R-Lube Axles Work On a Dexter D52 Nev-R-Lube Axle

Product Page this Question was Asked From

Continue Researching