Replacement 4 Way Trailer Connector for my PWC Trailer

Question

Question:

I have a Triton pwc trailer and looking to replace the wiring 4 pin connection. It does have 9 wires going to the 4 pins Do you have a replacement connector? Thx

asked by: Chuck

0

Expert Reply:

The Hopkins Endurance 4-Way Flat Trailer Connector part # HM48110 is the perfect solution to solve your problem. Use heat shrink butt connectors like DW05745-5 to ensure a water tight connection.

expert reply by: Randy B

0

Answer 1

Hey Jeff, I doublechecked the Curt Trailer Hitch Receiver #C13392 and #13432 as they are labeled with their capacities and also reached out to Curt for confirmation. After speaking with Curt we found that their website incorrectly listed the…

view full answer...

Answer 2

I spoke with my contact at Curt about trailer hitch #13432. The distance between the front and back mounting plates is 3-1/8 inches. This is a custom fit trailer hitch designed for 2007 to 2014 Jeep Wranglers, including Unlimited models. I have…

view full answer...

Answer 3

Yes, the Curt Trailer Hitch Receiver #C13392 you mention will fit your 2020 Jeep Wrangler. This hitch has a maximum towing capacity of 3,500-lbs, a maximum tongue weight of 350-lbs, and features a simple bolt-on installation. Attached is an…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement 4 Way Trailer Connector for my PWC Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching