Will the Timberens part # TNRTTN Work on my 2018 Nissan Titan with an Equalizer Weight Distribution

Question

Question:

Hi guys. I have a 2018 Nissan Titan, Platinum Reserve, Crew Cab, 2-wheel drive, with a Equal-I-Zer weight distribution hitch 10,000 lb. Towing a 7,700 lb ish, 2020 Forest River Wildwood 27RKS. Will the Timbren kit fit my vehicle? Thanks in advance.

asked by: Jon S

1

Helpful Expert Reply:

Great news! The Timbren Rear Suspension Enhancement System part # TNRTTN will work out great with your 2018 Nissan Titan and will work perfectly in conjunction with your weight distribution system..

With your equalizer system as part of the equation I recommend after installing the Timbrens that you re check the system per the instructions to ensure that the system is still optimized and does not need fine tuning.

expert reply by: Randy B

1

Answer 1

The Timbren install pictures you saw might have been from a different vehicle as the #TNRTTN that you referenced installs by attaching to the bottom of the bump stop bracket that you found.

view full answer...

Answer 2

The Timbren kit part #TNRTTN is a confirmed fit for your 2017 Nissan Titan and is going to provide you with additional suspension support when towing. Typically you don't need a kit like this if you already have weight distribution but if you are…

view full answer...

Answer 3

Thank you for providing a photo of your trailer coupler. Trailers should always be level when hitched. If a trailer is out of level when towed it will tend to have more sway. I notice you have weight distribution (WD) lift brackets on your trailer…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Will the Timberens part # TNRTTN Work on my 2018 Nissan Titan with an Equalizer Weight Distribution

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching