Will the No-Drill Bracket part # 18136 Work on a Round Hitch

Question

Question:

need the hm 40978 bracket have a round curt hitch will 18136 tighten up on a round bar? thanks

asked by: Ronald L

1

Helpful Expert Reply:

Yes the Tow Ready No-Drill Mount Bracket part # 18136 work great with round tube hitches. It is designed to flex around any shape solid object you want to mount it to.

expert reply by: Randy B

1

Ronald S.

6/3/2020

Works great!! Thanks

Reply

Answer 1

The two self tapping screws included with the Reese Multi-Plug Wiring Harness part #74682 will allow you to attach the trailer connector directly to your trailer hitch if needed but I don't really recommend this as you can weaked it and increase…

view full answer...

Answer 2

Maximum amperage draw for 4 Brakes that are 10 or 12 inch diameter is 15.0 to 16.3 amps at 12 to 13 volts. The 14 gauge wire may be sufficient but for maximum braking effectiveness at full load capacity. I would opt to run 10 gauge wire. Larger wire…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 9

Roof rack options for your 2014 Chevrolet Express Van with rain gutters are displayed on the linked page and these include products from Inno, Rhino-Rack and Thule. As you review the rack systems you will notice that their weight ratings vary…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 11

The Inno Square Crossbars part #INB165 and the Thule Square Load Bars part THLB65 are both 65" long x 1-1/4" wide x 7/8" tall so yes, they should work in place of one another just fine.

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Will the No-Drill Bracket part # 18136 Work on a Round Hitch

Product Page this Question was Asked From

Continue Researching