Is Hardware Included with ThinLine LED Trailer Tail Light # STL64RCB

Question

Question:

Will I need mounting hardware for the slim line led lights in my cart?

asked by: Paul

0

Expert Reply:

Yes you will need to provide the hardware for mounting the ThinLine LED trailer taillights part # STL64RCB that you referenced as it is not included. It's not included as not every application would be the same.

expert reply by: Jameson C

0

Answer 1

The Optronics LED Trailer Tail Light #STL42RB comes with the light assembly only, but we do have the following pigtail styles to choose from: - Right Angle 3-Wire Pigtail #A47PB - Straight 3-Wire Pigtail #A45PB

view full answer...

Answer 2

Since you are keeping your current taillights on your Grand Design 303RLS I recommend the ThinLine LED Trailer Tail Light #STL64RCB over the #STL64RB as they have a clear lens. When you use these during the day there will be a more pronounced…

view full answer...

Answer 3

The closest taillight solution we have to what you are looking for would be the part #STL264RCB which is a stop/turn/tail light that is an LED strip that measures 20-1/2 inches in length.

view full answer...

Answer 4

The Rampage SuperBrite LED Tailgate Light Bar #RA960134 will install using automotive grade adhesive tape and will plug directly into a 4 way trailer connector. If you don't already have that 4 way connection, I recommend the Curt Vehicle Wiring…

view full answer...

Answer 5

The Putco Red Blade LED Tailgate Combination Light Bar part #P92010-60 which is the lightbar I recommend for your trailer has LED lights so the amp draw will be very minimal. The reason that this is important is because the total amp draw for each…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Is Hardware Included with ThinLine LED Trailer Tail Light # STL64RCB

Product Page this Question was Asked From

Continue Researching