Flat Towing Trailer Wiring for 2007 Jeep Wrangler Unlimited

Question

Question:

Do i need this for a 2015 jeep grand cherokee with the 2 speed trasmition?

asked by: Don M

0

Expert Reply:

The # 42615 is a trailer wiring harness so would not be what you'd want for a flat towing setup. For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.

expert reply by: Jameson C

0

Answer 1

Yes the Roadmaster InvisiBrake Supplemental Braking System Item #RM-8700 will connect directly to your towed vehicle's battery and charge it while driving unlike most braking systems that would actually drain your battery. Some notes to…

view full answer...

Answer 2

The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, #HM56104 is not confirmed for the 2011 Jeep Wrangler Unlimited (It fits GM vehicles); you need the Hopkins part number, #HM56200. This harness requires no cutting, splicing into your…

view full answer...

Answer 3

The tow bar wiring I recommend for your 2014 Wrangler is the Hopkins Custom Tail Light Wiring Kit, part #HM56200. This system is not used with the 4-way connector you have on your Jeep for towing. Our installers have found that the trailer towing…

view full answer...

Answer 4

I have a great option but the Roadmaster Tail Light Wiring Kit for Towed Vehicles part #RM-152-LED is not a confirmed fit for your 2008 Jeep Wrangler JK Sahara edition. It comes down to the inserts being too long and interfering with the standard…

view full answer...

Answer 5

You can switch your Roadmaster InvisiBrake Supplemental Braking System #RM-8700 to a different vehicle - in your case a 2010 Chevy Equinox - simply with the Second Vehicle Kit for Roadmaster InvisiBrake Braking System #RM-98700. I have added a link…

view full answer...

Answer 6

Yes the Brake Lite Relay part #RM-88400 does fit with the Hopkins tow bar wiring kit part #HM56200 that you have. This is a required relay solution if you are using supplemental braking that depresses the brake pedal of the vehicle and your…

view full answer...

Answer 7

Both the Roadmaster Falcon #RM-520 and Falcon 2 tow bars, among others, are compatible with the Jeep D-Ring Bumper Mount kit #RM-035. The kit fits your 2014 Jeep Wrangler that has the off-road bumper with 3/4 inch thick D-Ring bumper mounts. Safe and…

view full answer...

Answer 8

The Hopkins Custom Tail Light Wiring Kit, Item #HM56200, is a confirmed fit for towing your 2015 Jeep Wrangler Unlimited. With regards to towing a trailer with your Jeep, the Hopkins Plug-N-Tow Connector, Item #HM41365, is not a fit. Instead, I…

view full answer...

Answer 9

You can add a BrakeBuddy charge line kit part #BB54FR to your flat tow setup that is using an Invisibrake part #RM-8700 and it wouldn't interfere. It would put an additional charge on the battery like you are wanting.

view full answer...

Answer 10

You can get the Second Vehicle Kit for Roadmaster InvisiBrake Braking System #RM-98700. This will give you everything you need to set up the invisbrake system in your Jeep cherokee. Additionally to this you will need the Replacement Cylinder for…

view full answer...

Answer 11

On the Roadmaster InvisiBrake Supplemental Braking System #RM-8700 you will adjust the braking pressure between the 5 psi minimum and the 80 psi maximum based on the behavior of your specific Wrangler XL as well as personal preference. The factory…

view full answer...

Answer 12

Typically when using D-Ring adapters #BX88357 you'll have to snake some shorter cables, like #RM-910648-20 around the frame rail of the vehicle and then out to the front of the vehicle to connect to your safety cables. There's no easy…

view full answer...