Can I Use the 2-1/2" Anti Rattle Hitch Pin for etrailer Cargo Carrier on a 2" Receiver

Question

Question:

I ordered item #e98874 and the hitch pin once threaded and installed is just a bit too short to put the clip on. Will the 2 1/2 inch hitch pin item #e98911 fit my cargo carrier? Thanks!

asked by: James G

1

Helpful Expert Reply:

This isn't completely uncommon since the receiver tubes on the Toyota factory hitches are a little bit thicker than what most other hitches are for some reason. With that said, you would be able to use the # e98911 on your etrailer Cargo Carrier # e98874 to secure it to the 2" hitch on your 2011 Toyota Sequoia.

expert reply by: Erik B

1

Answer 1

This sometimes happens and the best solution is to get the locking anti rattle bolt #e99047. It is a lot longer and can be locked so it's an upgrade for sure. This will work with your tilting cargo carrier #e98874 and other etrailer products as…

view full answer...

Answer 2

We sure do! To replace the anti-rattle hitch pin for your 24x60 etrailer Cargo Carrier #e98874 I recommend using the Threaded Anti-Rattle Pin Lock #e99047 so you take out any play in the cargo carrier moving in the receiver, plus it secures your…

view full answer...

Answer 3

Yes, you would be able to replace pin at the fold up shank in the 24x60 etrailer Cargo Carrier for 2" Hitches - Steel - Tilting - Folding - 500 lbs, part #e98874, with the Threaded Anti-Rattle Hitch Pin Lock for etrailer Cargo Carriers - Keyed…

view full answer...

Answer 4

The anti-rattle pin for the Folding 24x62 etrailer Cargo Carrier for 2" Hitches #e98872 can be replaced with the Threaded Anti-Rattle Hitch Pin and Clip #e98910 or upgraded to the Lock for etrailer Cargo Carriers #e99047.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The best hitch for a 2024 Subaru Outback is the etrailer item #e25TR. This hitch is custom fit and bolts to your Subaru with included hardware. This is a class III hitch with a 2" receiver, that has a 3,500 lbs towing capacity and a 350 lbs…

view full answer...

Answer 7

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I'm assuming your Express doesn't have the 7-way, but does have the capped round plug behind the bumper on the drivers side frame rail, you'll install part #30955. Simply remove the cap and plug the connector in. To wire up the controller…

view full answer...

Answer 10

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 11

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Answer 12

I have a set that will work however your 2023 Chevy Suburban's owners manual says not to use tire chains because of clearance issues on the inner part of the tires. You can find this information on page 370. To avoid damaging brake lines and…

view full answer...