Identifying 7-Way Circuit Wire Colors on 2000 Ford F-150

Question

Question:

On a 2000 f-150 , on the connector coming from the truck. below the blue wire on the plug witch is for the electric brakes there is an Orange wire that has been cut or broke . If you could help what dose this Orange wire go to either the auxiliary battery for trailer or reverse lights ?

asked by: Joey L

0

Expert Reply:

Since vehicle trailer wiring colors don't always match what they are supposed to be the easiest way to identify the circuit in question is to check out the picture I attached that shows the pin out of a 7-way.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The fuse on your 2000 Ford F-150 that is for the trailer right turn and stop lights is the number 19 fuse in the power distribution block in the engine compartment. If you check in your owner&#39;s manual on page 182 you can see the exact…

view full answer...

Answer 2

On the 7-Way Molded Trailer End Connector, #50-67-106, the reverse light wire is yellow. It is the wire attached to the center pole of the plug.

view full answer...

Answer 3

It sounds like you are looking for a 7-way solution to install in the bed of your truck because you have an in-bed hitch like a gooseneck or fifth wheel and need a 7-way closer to it. So for that we have the Curt #C56070 which provides exactly…

view full answer...

Answer 4

The wiring for the 7-Pin connector is different than the 7-Way blade connector. You will need an adapter to make the two different styles compatible. You can use the Adapter 7 Way (Blade) to 7 Way (Round Pin), #47595. The blade end plugs into the…

view full answer...

Answer 5

According to my research the following wires for the 7-Way on your 2019 Chevy Silverado 2500 should carry the following functions: Green OR White/Green - Reverse White - Ground Blue - Brake Controller Green OR Green/Purple - Right Turn/Stop…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...