Front and Rear Sway Bars that Fit 2019 Ford F-550 Motorhome with 22k GVWR

Question

Question:

Im looking for front and rear sway bars for a 2019 F550 motorhome 22K GVW V10 Can you help?

asked by: Robert K

0

Expert Reply:

I checked with Roadmaster and for your RV built on a 2019 Ford F-550 V10 chassis with a 22k GVWR the correct rear sway bar is the part # RM-1139-149 and the front bar is # RM-1139-148.

expert reply by: Jameson C

0

Answer 1

There certainly is! You'll want to use the Roadmaster #RM55VR Steering Stabilizer which is a fit for the 2019-2022 Ford F-550 Cab/Chassis that your Thor Magnitude Super C motorhome is built on. I've confirmed this with Roadmaster. The kit…

view full answer...

Answer 2

Based on the GVWR of your 2021 Thor BH 35 motorcoach the rear sway bar you'd want is the part #RM-1139-190 which makes the biggest improvement to ride quality and stability. Then for a front bar you'd want the part #RM-1139-148 which would…

view full answer...

Answer 3

You definitely can install either just the front or rear set of SumoSprings before the other. They do work best with them installed all around but people all the time will install on either the front or rear axle first and then later add the other…

view full answer...

Answer 4

Everything you are experiencing with the Roadmaster Front Anti-Sway Bar #RM-1139-148 is normal. The factory components use rubber bushings which tend to stick to the sway bar and prevent it from moving as freely as the Roadmaster of your 2015 Ford…

view full answer...

Answer 5

The correct anti-sway bars for your 2020 Thor ACE Motorhome are going to depend on the GVWR of your model. If you have a GVWR of 16,000 or 18,000lbs then you would want the Roadmaster Rear Anti-Sway Bar #RM-1139-146 for the rear. If you have a GVWR…

view full answer...

Answer 6

The correct Roadmaster steering stabilizer for your 2018 Thor Miramar 35.3 motorhome is the following: - Roadmaster Exact Center Steering Stabilizer #RM42RR This steering stabilizer comes with the mounting brackets, and I verified the fit for you…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Front and Rear Sway Bars that Fit 2019 Ford F-550 Motorhome with 22k GVWR

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching