Does the Shackle Angle have to be the Same Angle on both Sides of my Trailer Suspension

Question

Question:

On one side of my camper the angle is about 70 degrees. The other side is about 40 degrees. Both are angling toward the axel as they should. Is this a problem? One side sits about 1/2 to 3/4th of an inch lower. Thank you.

asked by: Terry B

0

Expert Reply:

Most likely you are fine and the difference in angle is due to the trailer sitting higher on one side than the other. I would still verify that the spring hangers are the same distance apart on both sides of the trailer, and that none of the other trailer components are not worn out.

For the 3-Leaf Spring # e57SR that you referenced the recommended distance between the hangers is 25-3/4 inches

expert reply by: Jameson C

0

Answer 1

It's okay to replace leaf springs with ones rated for more weight and pretty common to do so but keep in mind, the higher you go the rougher the ride will be. If you have a utility trailer then I'd probably opt for the higher rated 5,000 lb…

view full answer...

Answer 2

Assuming your springs have some age and some mileage on them, then they were likely 25-1/4 inch long springs. That is the typical size for 3,500 - 4,000 lbs double-eye leaf springs like part #e57SR. These are the springs I would go with if I were…

view full answer...

Answer 3

You can measure your leaf spring (eye to eye) while it is still installed on the trailer, but first you'll want to jack up the trailer so that the leaf spring is completely unloaded. Also, it is possible that your springs are worn and stretched…

view full answer...

Answer 4

In order to find the correct replacement leaf spring for a trailer you first need to start by noting the type whether that be slipper or double eye. Then, you'll need to measure their unloaded length via jacking up the trailer. If the springs are…

view full answer...

Answer 5

You can upgrade the 1750 lb leaf springs to 2500 lb leaf springs. You do want to keep in mind that the ride may be a bit stiffer since you are upgrading your springs to a higher capacity. Like you mention upgrading the springs will not give you a…

view full answer...

Answer 6

Regardless of the amount of leaves a leaf spring has if the capacity is the same between two of them they would both flex and bottom out the same. I would recommend you have your trailer and boat weighed so that you know whether or not you are…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 12

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Does the Shackle Angle have to be the Same Angle on both Sides of my Trailer Suspension

Product Page this Question was Asked From

Continue Researching