How Does Air Lift Air Suspension Kit Fit 1989 Chevy P30 Commercial Van

Question

Question:

AL88203 i HAVE A 1989 p30 COMMERCIAL STEP VAN WITH OVERLOAD SPRINGS. cAN i INSTALL THIS PRODUCT IN PLACE OF THE JOUNCE BUMPERS...RATHER THAN ON THE SPRINGS. oR DO YOU HAVE ANOTHER OPTION

asked by: David M

0

Expert Reply:

I attached an install diagram for the Air Lift kit part # AL88203 that fits your 1989 P30 step van and in it you can see it does not attach to the leaf spring and instead to the axle and the jounce bumper mount.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I recommend going with Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers #AL88203 for your rear axle. This kit is confirmed to fit your 1984 P30. These air springs have built-in jounce springs so that you get the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Yes, it is! Honda and other manufacture's like to leave the fuses out of new vehicles that do not come with a functional towing package to save on costs. You can verify if you're missing the fuses by checking your fuse box but I am pretty…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

How Does Air Lift Air Suspension Kit Fit 1989 Chevy P30 Commercial Van

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching