What Size Allen Wrench Is Needed to Remove the 2 inch Adapter on the Trailhead Bike Carrier

Question

Question:

What size allen wrench is needed to remove the allen bolt that holds on the spacers?

asked by: David C

0

Expert Reply:

I spoke with my contact at Swagman and she informed that the size Allen wrench needed to remove the 2 inch adapter is 6 millimeter.

I attached installation instructions for this product for you to check out also.

expert reply by: Jameson C

0

Answer 1

The Swagman Trailhead Bike Rack item #S63360 has a distance of 13-7/8" measured from the outside of the support arms. The bars are close to 1" thick so if you measure from inside to inside you'll get right around 11-1/2" so…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 5

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...

Answer 8

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 9

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 10

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 11

I have the perfect bike rack for your Electra Townie and for this I recommend the Saris Freedom 2 Bike Platform Rack part #SA4412B. The reason I recommend this bike rack over the Malone rack is because you don't need to use an adapter bar at all.…

view full answer...

Answer 12

I can help you choose between the Kuat Sherpa 2.0 and Kuat Transfer V2, as both are really nice bike racks. Let me start off, since you mentioned 3-bike rack, if that's what you were after you would need the Kuat Transfer V2 Bike Rack for 3 Bikes…

view full answer...

What Size Allen Wrench Is Needed to Remove the 2 inch Adapter on the Trailhead Bike Carrier

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching