Does Mounting Hardware Come with Jif Marine 2K Single-Speed Boat Trailer Winch

Question

Question:

Does mounting hardware bolts come with winch?

asked by: Zac

0

Expert Reply:

The Single-Speed Boat Trailer Winch with 20' Strap and Brake # 315-W2000D does not come with mounting hardware. This is basically because there are a wide variety of mounting applications so you'll need to supply your own mounting hardware, which you can acquire at your local hardware or home improvement store.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 6

The Ratcheting Handle for Dutton-Lainson Pulling Winches #DL70371 has a 27/32" diameter slot with 7/16" width. If you can tell me the diameter and width of your slot and thread pattern I can verify if we have another handle which will fit.…

view full answer...

Answer 7

From what I have found, the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed - 1,800 lbs #DL14627 will match the bolt pattern of your Shelby 5407B. I have attached a diagram as well as the dimensional drawing showing the bolt pattern on…

view full answer...

Answer 8

Yes, the strap on the #315-W3200D can be installed so that it comes from the bottom instead of the top. However, doing so will reverse the switch and the direction you turn the handle for operation. The self-locking mechanism will work either way.…

view full answer...

Answer 9

I went out to our warehouse to take some measurements of the mounting base on the Fulton Single Speed Trailer Winch #F142306. The plate itself measures 6 inches long and 4 inches wide. The mounting pattern features a few oblong holes that allows it…

view full answer...

Answer 10

The 3,200 lb 2-Speed Boat Trailer Winch with 20' Strap and Brake #315-W3200D will be sufficient to pull in your 3,190 lb boat if your trailer has rollers on it as that will make your boat easier to move. If you have bunks then it will technically…

view full answer...

Answer 11

A Nylon Bushing #TRBU11561 is not required to be used on the open end of the 4-Leaf Slipper Spring #e33SR. Since the bushing is not going to be fully encased it stands that under the weight of the trailer it will fail and break apart more easily. I…

view full answer...

Answer 12

The 4-Leaf Slipper Spring w/ Open Eye End for 4,300-lb Trailer Axles - 26-1/4inch Long Item #e33SR that you referenced does not require an additional bushing for the hook end to attach to the rear hanger. The hook end of the spring will rest on the…

view full answer...