Gooseneck Coupler Lock for Kaufman Trailer

Question

Question:

I need a ball lock for my gooseneck Kaufman trailer what do u recommend

asked by: Sam

0

Expert Reply:

The correct lock for your Kaufman gooseneck trailer is the Blaylock EZ Lock Gooseneck Coupler Lock # BLTL-55-40D (which I confirmed with my contact at Kaufman). If you'd like a lock for the set screw as well then you can use the kit # BLTL-57-40D2 instead which includes both the lock for the coupler section and the set screw.

expert reply by: Jon G

0

Answer 1

From what you are describing it sounds like you are used to towing a bumper pull trailer with your 2017 pickup. When towing with a gooseneck hitch like the B&W #BWGNRK1111 the turning point is located directly above your rear axle and not at the…

view full answer...

Answer 2

Thank you for the photo of your coupler. When choosing a lock for the coupler it makes it much easier if you are able to identify the coupler manufacturer. The Blaylock EZ Lock Gooseneck Coupler Lock, part #BLTL-55-40D is designed to fit RAM…

view full answer...

Answer 3

If you have a gooseneck trailer then we do have an option for your trailer side with the B&W Extend-A-Goose Gooseneck Coupler #BWTEXA4200. It has a 10" offset and has an outer diameter of 4". For something that site between the hitch…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Gooseneck Coupler Lock for Kaufman Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching