Is B&W Clevis Adapter Compatible with 1" Diameter Pin

Question

Question:

What clevis attachment will work on a BandW multi hitch with a 1inch hole?

asked by: Sidney C

0

Expert Reply:

We have 3 different adapters for a B&W Tow & Stow and it all just depends on the size of your hitch receiver:

2" - # BWTS35100B
2-1/2" - # BWTS35200B
3" - # BWTS35300B

These have 1-1/8" diameter holes for the clevis pin and will do just fine if you're going to be towing at slower speeds. If you will be towing at higher speeds then we'll want to get you something that has 1" diameter holes just to help eliminate play. For example, BulletProof Hitches has their 2-Tang Clevis # 358CLEVIS (with the 1" pin) which can be used with any of the following per the hitch receiver size:

2" - # HD206
2-1/2" - # HD256
3" - # HD306

expert reply by: Jon G

0

Answer 1

Unfortunately, the Clevis Adapter for 2 inch hitch ball mounts, part #BWTS35100B, is only rated for up to 10,000 pounds. The #BWTS35200B you asked about measures approximately 2-3/4 from center on center between the mounting holes and the pins have a…

view full answer...

Answer 2

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 3

The B&W Silencer Pad #BWTS35020 is intended to be placed on the shank of one of their Tow & Stow Multi-Ball Mounts like #BWTS10048B so that it acts like a gasket between the collar on the end of the hitch's receiver tube and the…

view full answer...

Answer 4

The Clevis Adapter for B&W Tow & Stow 2-1/2" Ball Mounts #BWTS35200B that you referenced spans the 3 holes as you can see in the first attached photo. The other photo that you are referring to (with the 2 consecutive holes) is a…

view full answer...

Answer 5

The Timbren Trailer Suspension Enhancement System Light-Duty Trailers 1,000 lbs #TTRA1702 will be a great help in reducing body roll and helping dampen the bounce. Based on your measurements this will immediately take on load and stabilizing while…

view full answer...

Answer 6

The Timbren Trailer Suspension Enhancement System #TTRA1702 is 2-3/4" tall with no load on the spring. This particular system is designed to mount to the frame with the included bracket(see image) and when the suspension compresses the axle will…

view full answer...

Answer 7

The B&W Tow & Stow 3-Ball Mount part #BWTS30048B is designed for a 3" receiver tube opening therefore if this is what you have on your 2006 Ford F-250 then yes, it will work for you. However, if I had to guess I would say that you have a…

view full answer...

Answer 8

The Replacement 10K Ball Mount Tongue for Brophy Adjustable Drop Hitch #RTB1 will not fit the Curt Weight Distribution Shank for 2-1/2" Hitches #C17131 as #RTB1 only fits Brophy Shanks. Instead, what will work with the Curt WD Shank #C17131 is…

view full answer...

Answer 9

For your Curt Adjustable Ball Mount part #C45900 you'd have to stick with using the Curt dual sided hitch ball part #C45912 as the part #RTB1 only fits a Brophy shank.

view full answer...

Answer 10

According to the review video we have of the Brophy #RTB1 ball platform those holes used to vertically adjust this piece are 2" apart on center. It kind of sounds like you have a shank for a weight distribution system as the 1-1/4" height…

view full answer...

Answer 11

The distance between the mounting holes of the #RTB1 is 2 inches. The diameter is 5/8 inch.

view full answer...

Is B&W Clevis Adapter Compatible with 1" Diameter Pin

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching