Which Aries Grille Guard Hardware Kit Fits 2003 Ford Ranger

Question

Question:

Are these the correct brackets for a 2003 Ford Ranger XLT? If so do yall have a picture of the brackets?

asked by: Chris J

0

Expert Reply:

The Aries grille guard replacement hardware part # AABRKT-3053 is correct fit for your 2003 Ford Ranger since the grille guard # AA3053 does fit your truck.

I attached a picture of the brackets for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

If you have this Aries Grille Guard #AA3045 on your 2000 Ford F-250 then you need this hardware kit #AABRKT-3045.

view full answer...

Answer 7

Anything that mounts to the front of the 2016 Ram 3500 has the potential to interfere with the sensors at the front of the truck. The Parksense feature can be disabled using the button so that the sensors don't alert you all the time but when off…

view full answer...

Answer 8

The recommended ball for the Fastway E2 Weight Distribution Hitch #FA92-00-0800 that you have is 1-1/4 inch in diameter and with a length of 2-5/8 inches. For a 2-5/16 inch ball with those dimensions I would recommend the #C40030.

view full answer...

Answer 9

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 10

I recommend the Tow Ready Custom Fit Vehicle Wiring Harness #118554 for your 2012 Jeep Liberty. This harness will provide you with 4-way flat connector at the rear of your vehicle. It will plug into the back of each taillight assembly on your…

view full answer...

Answer 11

We can help you with installation of a 7-way trailer socket on your 2011 Jeep Liberty. First, since you have no trailer connector at all on the vehicle we'll start with a 4-pole flat trailer harness and then simply add the 7-way. The best option…

view full answer...

Answer 12

For the 2012 Jeep Liberty, I recommend the Curt Trailer Hitch #13245. This is a Class III rated trailer hitch with a 2 inch hitch receiver. This hitch has a maximum gross trailer weight of 5,000 pounds, but I recommend checking your vehicle's max…

view full answer...

Which Aries Grille Guard Hardware Kit Fits 2003 Ford Ranger

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching