Lug Seat Angle of Dexstar Galvanized Steel Spoke Trailer Wheel # AM20134

Question

Question:

What is the correct wheel lug angle for this wheel?

asked by: Steve

0

Expert Reply:

The Dextar Galvanized 12" Steel Wheel you mentioned, part # AM20134 uses a standard lug bolt or nut with a 60 degree lug seat.

expert reply by: Mike L

0

click to enlarge

Answer 1

The etrailer.com Trailer Hitch Receiver part #E98841 when we installed it on a 2013 Hyundai Santa Fe was 13&quot; from the ground to the top inside edge of the receiver tube. I called U-Haul and they said that the coupler height of the 4x8…

view full answer...

Answer 2

For a 12 inch wheel/tire combo, I&#39;d recommend the Kenda Karrier ST145/R12 tire on a 12 inch powder coated steel wheel, part #AM35354. This is a radial tire that will run cooler than a bias ply at highway speeds, however the tire is rated…

view full answer...

Answer 3

For a 12 inch wheel and tire we have the Kenda Karrier S-Trail part #AM31202 which has a ST145/R12 tire size mounted on a wheel with a 5 lug bolt pattern and has a 81 mph speed rating.

view full answer...

Answer 4

Sorry for the confusion. The Kenda Karrier ST145/R12 Radial Trailer Tire with 12&quot; Black Mod Wheel #AM353354 that you referenced at one point was rated for 65 mph but now is rated for 81 mph.

view full answer...

Answer 5

The difference in section width between a 5.30-12 and a 145/12 is just 0.1 inches. Only half of that is applied towards the trailer. On wheel and tire combo #AM35354 the wheel is a black mod wheel with a zero offset meaning that the mounting…

view full answer...

Answer 6

We've got just what you're looking for on the tire front, and a few different options you could use for wheels. To replace your 5.30-12 tire I recommend using the Taskmaster #TT53012C, which are a radial tire that's perfect…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Lug Seat Angle of Dexstar Galvanized Steel Spoke Trailer Wheel # AM20134

Product Page this Question was Asked From

Continue Researching