Recommended Replacement for Shelby Winch 5352 for Boat Lift With Wheel

Question

Question:

shelby model 5352. want to replace this winch currently on a boat lift with a wheel for cranking. Which model would work ?

asked by: Chuck

0

Expert Reply:

The winch I highly recommend to replace your Shelby 5352 winch is the Dutton-Lainson Hand Winch # DL14927.

This winch has the same 1,500 lb capacity as the Shelby, an automatic brake, is designed for use with a boat lift and can be used with a wheel.

I have added a link to a video review for you to check out as well of the Dutton-Lainson Hand Winch # DL14927.

expert reply by: Kyle S

0

Answer 1

Some Shelby winch models used a handle that secured to the winch with an Allen key. If this is the type you have then it is possible that the set screw or the post on the winch the handle attaches to is stripped or worn to the point that the handle…

view full answer...

Answer 2

While we don't have a repair kit for your Shelby 5352 winch we do have a great replacement winch to match what you have since it is a 1,500 lb brake winch. For that you'd want the Dutton Lainson 1,500 lb Winch Part #DL14996 which would be a…

view full answer...

Answer 3

The winch that I recommend you use to replace your Shelby 5352 winch with automatic brake and 1,500 lb. capacity is the Dutton-Lainson Hand Winch w/ Automatic Brake #DL14927. The Dutton-Lainson Hand Winch w/ Automatic Brake #DL14927 has the same…

view full answer...

Answer 4

We can help you with a winch but not with a large wheel like in the picture you mentioned. They have several winches designed for boat lifts and those winches are compatible with the big wheel you mentioned. These include the following: Heavy Duty…

view full answer...

Answer 5

For your Jet Ski Lift, I recommend the Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish - 1,500 lbs #DL14927 or the 2,500 lbs #DL14958. These winches are designed for use on boat lifts and have the covered gears for safety. They both…

view full answer...

Answer 6

The left hand version of the Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish part #DL14927 is Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish - Left Side Handle part #DL16331. The capacity of the left hand winch…

view full answer...

Answer 7

I went out into our warehouse to grab a Dutton Lainson Winch part #DL14627 to measure the bolt hole dimensions for you. I attached a picture that has all of them listed.

view full answer...

Answer 8

The Dutton-Lainson Brake Winch with TUFFPLATE Finish #DL15721 has the following dimensions: Handle - 9-3/4 Mounting plate - 7 long x 4-1/2 wide x 5 tall Mounting plate to furthest point of gear - 9-1/2 Mounting plate to top of gear - 7-1/2 Large hole…

view full answer...

Answer 9

I looked up your trailer jack info and it was a 1,600 lb hand winch that hasn't been made in quite some time. Most refer to it as a "vintage" hand winch. Sounds like you got a lot of life out of but there's nothing we offer beyond…

view full answer...

Answer 10

The Cable Clamp for Pulling and Brake Winches by Dutton-Lainson #DL24350 is compatible with 1/4 inch stainless Steel winch cable like the Hand Winch Cable with Safety Hook 1/4" Diameter x 50' Long - 3,500 lbs #DL24104. You can also use the…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Recommended Replacement for Shelby Winch 5352 for Boat Lift With Wheel

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching