How Many Assemblies Come With the Electric Trailer Brake Kit AKEBRK-35

Question

Question:

Just to be clear...... this is for two backing plates , two magnets,and all brake shoes....minus mounting hardware

asked by: Dot

0

Expert Reply:

Yes, the Electric Trailer Brake Kit part # AKEBRK-35 comes with two complete braking assemblies or enough for one axle. The hardware is not included but if you need this we have it as Mounting Hardware for 10" Brake Assemblies part # BRKH10B.

expert reply by: Conner L

0

Answer 1

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 2

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 3

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 4

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

For a 3,500 lb hub/drum replacement that will work well to replace your AL-KO 8500 you'd want the hub part #84546UC3-EZ which fits the spindle and has the 5 on 4-1/2 inch bolt pattern you need. For brake assemblies then the Electric Brake…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

I was able to find the 126003 hub and was able to determine that it is a 3,500 lb hub/drum with a 5 on 4-1/2 inch bolt pattern just like the #AKHD-545-35-K that you referenced. This hub will work as a replacement for your Lippert.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 11

If what you have now Chad is pretty flat at 26 inches then the best replacement size would be 25-1/4 inches like you mentioned. Since you wanted to increase the capacity you would want the part #e57SR which is for 4k trailer axles.

view full answer...

How Many Assemblies Come With the Electric Trailer Brake Kit AKEBRK-35

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching