Hitch Pin Lock with 5/8 inch Diameter and 3-1/2 inch Span

Question

Question:

I need a 1/2 inch diameter by at least 3 1/2 inch long locking pin. Do I have to by both?

asked by: Lance H

0

Expert Reply:

We have a pin lock that's sold individually that has the 3-1/2 inch span you need with the same diameter as the # AM3493 but the included lock of this is 5/8 inch which is the standard hitch pin size. So for that we have the # WS05 which has a 3-1/2 inch span and a 5/8 inch diameter. For the larger hitch sizes like 2 inch and up (including 3 inch) the diameter hitch pin used is 5/8 inch.

expert reply by: Jameson C

0

Answer 1

I have a solution for you. Andersen has the Trailer Hitch Lock #AM3493 that is designed to be used with the Andersen EZ Heavy Duty Adjustable Hitch, #EZ Heavy Duty Adjustable Hitch. The Andersen hitch lock pin is made of stainless steel with aluminum…

view full answer...

Answer 2

According to Andersen, they do not recommend using any pins to attach the ball housing to the weight distribution system's shank which includes the Andersen Trailer Hitch Lock and Adjustment Pin Lock Set part #AM3493. They recommend that you use…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Hitch Pin Lock with 5/8 inch Diameter and 3-1/2 inch Span

Product Page this Question was Asked From

Continue Researching