Will the Curt Trailer Hitch fit a 2011 Jeep Liberty With Full Size 235/70-16 Spare

Question

Question:

Which 2” hitch will fit a full size spare for my 2011 Jeep Liberty 4x4 with a 235-70-16” spare tire.

asked by: Eddie

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13245 which is a fit for a 2011 Jeep Liberty will work on models with the factory full size spare tire. If the 235/70-16 is the factory size spare tire then you won't have any issues. That said, I don't have a list of specific tires sizes that the hitch will work with but so long as this has not been changed out from the factory you will be good to go.

I have attached a photo of the hitch installed with a full size spare tire for reference.

expert reply by: Conner L

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

For your 2012 Jeep Liberty Sport 4WD, I recommend the Roadmaster EZ Base Plate Kit - Removable Arms #521433-1 to start your flat tow set-up. I've attached a video of this installation to help. For a tow bar, I recommend the Roadmaster Falcon 2…

view full answer...

Answer 4

Flat towing a vehicle requires specific equipment to tow the vehicle safely and in accordance with local, state, and federal laws. A front mount hitch is not suitable for use to flat tow a vehicle behind an RV but I can tell you all of the parts that…

view full answer...

Answer 5

The bolts that come with the Curt hitch part #C12245 are size M12x7.75. We also sell replacement hardware for all of the hitches we offer with the part #RHK.

view full answer...

Answer 6

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 7

Which connector does your vehicle have on the rear bumper? If it's the 4 pole flat connector, you'll need the Brake Controller 7 & 4 Way Installation Kit - 10 Gauge, part #ETBC7, hardwired brake controller installation kit. We have an FAQ…

view full answer...

Answer 8

For your 2010 Jeep Liberty, I recommend you start with the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118554. This will connect to your factory wiring behind your tail lights. Then because you are wanting to run a…

view full answer...

Answer 9

Trailer hitch installs and trailer wiring installs are totally separate processes. It wouldn't be a situation where "well, you're already half way there may as well do the wiring too." So if you wanted to start with a hitch now like…

view full answer...

Answer 10

Assuming that the military version of the 1985 Chevy C/K series trucks has the same tail light configuration as the civilian models you would start by installing a 4-Way connector using #C55312. If it does not have the proper connectors for this…

view full answer...

Will the Curt Trailer Hitch fit a 2011 Jeep Liberty With Full Size 235/70-16 Spare

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching