Replacement Spring-Loaded Turnbuckle for HappiJac Qwik-Load Turnbuckle Set

Question

Question:

Im looking at this item and would like to know exactly what parts are included. Is the handle included? Everything in the photo? Also what is your return policy if there are missing or broken parts? My truck is a 2014 F350 Super Duty Lariat.

asked by: Candace

0

Expert Reply:

Yes the handle is included for the Replacement Spring-Loaded Turnbuckle for HappiJac Qwik-Load Turnbuckle Set # LC182897. So everything in the photo is included like what you were asking.

I am attaching a link to our returns policy for you to reference as well.

expert reply by: Jon G

0

click to enlarge

Answer 1

All 2017 F-Super Duty vehicles equipped with a factory trailer brake controller (TBC) utilize a trailer module (TRM) which initiates the trailer charging system. For trailer charging to operate, the TRM must detect a trailer is connected and a brake…

view full answer...

Answer 2

I checked with Happijac and the kit you need for your 2011 Ford F-250 is the part #LC182910-182971 for the tie downs and then for the turnbuckles #LC182897. This is a much better setup than a stake pocket attachment for a camper so I would not…

view full answer...

Answer 3

The correct frame mounted tie downs for your 2012 Ford F-250 short box are the HappiJac Truck-Mounted Camper Tie-Downs #LC182910-182971 which work as long as you do not have a Torklift aftermarket hitch. This includes: - (2) Front anchor plates - (2)…

view full answer...

Answer 4

The HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 have a minimum reach of 16-1/2". This means your tie-downs need to be at least 16-1/2" away from the attachment points on your camper. The best way to determine fitment would…

view full answer...

Answer 5

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to a…

view full answer...

Answer 6

A lot of times the 12 volt accessory circuit isn't active on vehicles for the trailer wiring. Sometimes it's just a matter of inserting or replacing a fuse under the hood of the vehicle. Or in other times a relay has to be installed.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...