Replacement Brackets for Westin MAX Tray that Fits 2013 Chevy Silverado 46-23615

Question

Question:

I need to replace the brackets on my Westin Max winch tray part number 46-23615 for a 2013 Chevrolet Silverado 2500hd are these the right brackets?

asked by: Eric H

0

Expert Reply:

The correct replacement hardware kit you need for the Westin Max Winch Tray you have part # 46-23615 is the part number # 46-2361PK. The kit you mentioned fits a different vehicle and would not work for you.

expert reply by: Jameson C

0

Answer 1

It is difficult to say if it will work for your application since we do not carry the Barricade Bull Bar, but it does look like the Parking Sensor Relocation Kit for Westin Sportsman Grille Guard #40-0005S is the best option for you. It will work as…

view full answer...

Answer 2

Since the correct Westin HDX Grille Guard for your 2021 Chevy Silverado 1500 is the part #57-3955 the correct replacement hardware kit would actually be the part #W78XV.

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Replacement Brackets for Westin MAX Tray that Fits 2013 Chevy Silverado 46-23615

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching