Does The Yakima FrontLoader Wheel Mount Bike Carrier Need 2 Load Bars On LoadWarrior

Question

Question:

I know for two Frontloaders you need two load bars when attaching the Frontloader to the LoadWarrior. If I have one Frontloader, do I still need two load bars to attach it to the LoadWarrior?

asked by: Kalei

0

Expert Reply:

The Yakima FrontLoader Wheel Mount Bike Carrier - Roof Mount part # Y02103 attaches to two crossbars so you would need two load bars on the Yakima LoadWarrior Roof Rack Cargo Basket part # Y07070. If you do not have 2 load bars you will need 2 of part # 8870042. I have attached a video of how the FrontLoader attaches.

expert reply by: Heather A

0

click to enlarge

Answer 1

What you are going to want to give you more stability for your kayak rack is the Rhino-Rack T-Load Hitch Mounted Load Bar #RTL002 installed in a 2 inch hitch on your 2016 Subaru Outback Wagon like part #75673. This will give you a third crossbar at…

view full answer...

Answer 2

Thank you for the purchase! Yes, the diameter of the tubing for the Rhino-Rack XTray Pro Cargo Basket #RRRMCB03 is 1". I confirmed this with my contact at Rhino-Rack.

view full answer...

Answer 3

I do have an option for you but in order to carry both a bike rack and spare tire you are going to need to go with an option that has both or else you would not have space. The Inno Shaper 80 Roof Cargo Basket is wide enough to fit your spare tire…

view full answer...

Answer 4

The tubing that the Yakima LoadWarrior Cargo Basket is constructed of also has a 1 inch diameter. The top tubes of the LoadWarrior are 38-1/2 inches apart, if the sides of your basket are closer than that, you'd need to shorten the load bar.

view full answer...

Answer 5

You do not need to take apart your Loadwarrior to install the replacement loadbar part #8870042. You would take off the end caps of the bar and then push them over the railing of the basket and attach to the load bar once that's accomplished.

view full answer...

Answer 6

There is a bar for the Yakima LoadWarrior Cargo Basket #Y07070 or #Y07070-74 which will work in a similar way to the accessory bar you mentioned. What you can use is the Replacement Loadbar For Yakima LoadWarrior #8870042. Even though it is…

view full answer...

Answer 7

For a crossbar designed to fit the Yakima Loadwarrior like part #Y07070 you would want the part #8870042 that is a crossbar designed for the Loadwarrior. This will attach to the side rails of the basket and will provide you with a crossbar like you…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 11

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 12

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...