Lock Set Recommendation for B&W Tow & Stow 3-Ball Mount

Question

Question:

I know that I need one to secure the mount to my hitch receiver, but do I need one or two more to secure the ball mount to the hitch?

asked by: Tim

0

Expert Reply:

If you want to totally lock the B&W Tow & Stow 3-Ball Mount # BWTS10048C you would need a lock set that locks the shank to the hitch and locks for the platform then to the shank with the InfiniteRule Locking Pins # 34061775-D.

expert reply by: Jameson C

0

Answer 1

The InfiniteRule Locking Pins for B & W #34061775-D would be the lock set you would want if you have the B&W Tow and Stow because it will provide you with a lock for each pin location on the hitch. If this is not the B&W hitch that you…

view full answer...

Answer 2

The B & W Tow and Stow 3-Ball Mount part #BWTS10049B has a built in anti-theft design that ensures ball mount platform can't be removed when Tow & Stow is installed into the hitch. Then to lock the 3-Ball Bount into the shank to prevent…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could also…

view full answer...

Answer 9

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 10

Yes there is! The Husky 31326 hitch is made to fit the industry standard fifth wheel rails (ISR). The Curt Adapter #C88KR is also made to the same industry standard measurements. So the Curt Adapter #C88KR will be exactly what you need to use your…

view full answer...

Answer 11

The Westin Custom Fit Truck Bed Mat #W55XV is the best option for your 2024 GMC Sierra 1500 with the 5-3/4' bed because it has a thick durable rubber construction as well as grooves running front to back of the bed to make it easier to clean out…

view full answer...

Answer 12

Hey Vernon, so the puck systems of the Ram and Chevy trucks are different so you wouldn't be able to use your current B and W Companion slider as-is in the bed of your 2024 Chevy Silverado 3500. So if you wanted to reuse the head from your…

view full answer...

Lock Set Recommendation for B&W Tow & Stow 3-Ball Mount

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching