Mounting Bracket Recommendation for a Optronics Thin Line Clearance Light

Question

Question:

Need to know what bracket you need to mount this light?

asked by: Chris

0

Expert Reply:

There are three available brackets that will work with the Optronics Thin Line Series Clearance Light # MCL63CRB. There is a black one part # A65PB, a gray one part # A66PB and a chrome one part # A67CB.

Check out the review video I attached for the # MCL63CRB.

expert reply by: Jameson C

0

Answer 1

We do have the parts you need to complete installation of the light. But first, sealed, Miro Flex, Mini Thin Line LED Marker or Clearance Light #AL191AB does not include a base or wiring harness. We have the compatible bases listed as related…

view full answer...

Answer 2

The Chrome Bracket and Single Wire Plug #A67CB has just enough room to route the wire that it comes with. Based on the photo you attached, it looks like the hole that is already drilled is in the exact spot for the wire on the new bracket to fit…

view full answer...

Answer 3

There are five mounting brackets available that fit the Optronics Trailer Clearance Side Marker Light #MC65AB. These three are all black plastic. They are Optronics #A65PBPG, #A65PB and #A65B. The first two come with a single wire, the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...