RV Steps Only Come Out With Engine On

Question

Question:

My rv steps will come out if my engine is running, but they wont if i cut the engine off. Do you have any ideas of what is going on. i have a 2005 fleetwood discovery. class A

asked by: Peggy O

0

Expert Reply:

I would first check for a switch just inside the door of your coach. In most cases there is a switch on the step system to shut it down so it doesn't move in and out( labeled Entry Step). There will be an override there that allows it to operate when the vehicle is started so if you didn't pull them back in they will retract automatically. This can also deploy the steps when the door is opened overriding the switch.

Another cause can be that the main 12V supply switch is turned off and that the steps aren't getting the power they need to operate when the coach is not running. This switch is often located right in that same area as the step switch. If you don't see it there check your coach's manual and it will indicate where it is located.

If both of these switches are in the correct position and you are still experiencing this issue please let me know and I will do what I can to get it resolved for you.

expert reply by: Randy B

0

Answer 1

Most powered RV steps are wired up so that if you turn on the RV the steps will automatically retract. If yours is extending instead that would indicate that this circuit is wired backwards. Do you know what steps you have?

view full answer...

Answer 2

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 3

It could possibly be the motor, door switch, gearbox, or control module. My first recommendation would be to check the power and ground as this is typically the cause of irregular behavior. I also recommend checking for any obstructions that could be…

view full answer...

Answer 4

The difference between the #RM-195125 and the #RM-195225 is that they are designed for different sized wheels; the #RM-195125 is designed to handle up to 16.5" tall wheels where the #RM-195225 can hold between 16" and 24.5" tall…

view full answer...

Answer 5

The heating element on your Atwood model GC10A-4E water heater (our part #AT94022) should be on the backside of the unit, towards the bottom of the tank. It will actually be behind the gas line assembly, which will need to be loosened and moved out…

view full answer...

Answer 6

It sounds like you have an RV on a Sprinter Cutaway Chassis. If your RV has a 2 inch hitch, and the distance from the hitch pin hole to the furthest edge of the rear bumper is less than 10 inches, you could use the Roadmaster #RM-195225 hitch mounted…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

RV Steps Only Come Out With Engine On

Product Page this Question was Asked From

Continue Researching