Install Picture of Draw Tite Hitch 76046-SK on Chrysler Pacifica

Question

Question:

any picture of this one? 2020 pacifica or even a 2019

asked by: Harvey J

0

Expert Reply:

I attached an install picture for the Draw Tite hitch part # 76046-SK that you referenced on a similar 2020 Chrysler Pacifica for you to check out. It's not a hybrid model in the picture but it would look the same on your hybrid model.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your 2019 Chrysler Pacifica Hybrid I highly recommend the Draw-Tite Max-Frame Trailer Hitch Receiver #76046-SK because of its hidden design. This particular hitch (which includes custom brackets specifically designed for the Hybrid model of…

view full answer...

Answer 2

The Curt #C29UR and the Draw Tite part #76046-SK are definitely the most hidden options for your 2021 Chrysler Pacifica Hybrid but the edge goes to the Curt in terms of least visible since the safety chain loops are horizontal and smaller. I…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Install Picture of Draw Tite Hitch 76046-SK on Chrysler Pacifica

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching