Is There a Driver Side DeeZee Specialty Series Wheel Well Toolbox

Question

Question:

is there a right and left side

asked by: Eddie H

0

Expert Reply:

Yes, we do carry a drivers-side wheel well toolbox like the DeeZee Specialty Series Passenger-side Wheel Well Toolbox, # DZ94B.

You will want to look at the DeeZee Specialty Series Driver-Side Wheel Well Toolbox, # DZ95B. I have attached a link to this product for you. The photo on the product page is a generic photo that shows the toolbox on the passenger side, but this is the driver side toolbox to accompany the passenger side toolbox that you referenced.

expert reply by: John H

0

Answer 1

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is…

view full answer...

Answer 2

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

I got some information from Yakima and included a diagram of the EXO SwingBase #Y34VR, which is the base part for the EXO SwingBase 2 Tier #Y82VR. Though the measurement from the pin hole to the closest edge of the carrier is not included in said…

view full answer...

Answer 5

The 7 inch Dexter Brake Assemblies like the part #23-48 do use clips to attach the magnets to the assemblies. I went and pulled one from our warehouse and found that in order to attach the magnet to the arm you would need to slide the magnet over…

view full answer...

Answer 6

Yes, the UWS Truck Bed Fender Well Toolboxes do require drilling for installation. The holes that will need to be drilled will be located wherever you choose. The recommended method is on the inside edge of the bed rail but you can also do so to…

view full answer...

Answer 7

Trailer hitch pins and locks do not have an official capacity because they would be rated well beyond what the hitch and vehicle are capable of. In other words, the hitch or vehicle would fail long before the locking hitch pin #e98880 would.

view full answer...

Answer 8

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...

Answer 9

I took a look at the installation for your Ultra-Flex Tri-Fold on your 2017 Chevrolet Silverado 3500 and it looks like it completely covers the sides of your bed rails where the TruXedo Truck Luggage Expedition Truck Bed Cargo Management System…

view full answer...

Answer 10

The Installation Hardware for Lippert Components Tailgate Storage System #LC373965 is designed to attach to a 2x4 steel bumper extension that goes in between the i-beam frame on your trailer and the 4x4 steel bumper. There also need to be at least…

view full answer...

Answer 11

Since you do not have the 4" of clearance to mount the Installation Hardware #LC373965 for the Lippert Components Flip Down Slotted Bike Rack Tailgate Storage System #LC243621, you will need the Lippert Tailgate Storage System Mounting Kit -…

view full answer...

Is There a Driver Side DeeZee Specialty Series Wheel Well Toolbox

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching