Phoenix Electric Trailer Jack Mounting Bracket to the top of the Jack Dimensions

Question

Question:

Please confirm the total height from mounting flange to top for UF38-944040. A dimensioned photo in one of your reviews shows it to be 18.9inch however Ultra Fab shows it to be 22.75inch on their website.

asked by: Richard G

1

Helpful Expert Reply:

The total height from the mounting flange to the top of the Phoenix Electric Trailer Jack Phoenix Electric Trailer Jack is 22.75". The overall height is 33". I have attached a diagram for your reference.

expert reply by: Heather A

1

click to enlarge

Answer 1

From the center of the bracket to the bottom of the wheel, the jack is 13 inches when it is fully retracted. From the top mounting hole to the bottom of the wheel, the jack is 15 inches when fully retracted.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 6

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 7

The rule of thumb for estimating a tongue weight is 10-15 percent of trailer weight. A 4,600 pound trailer would have a tongue weight between 460 and 690 pounds. Somewhere between a 1,000 to 2,000 pound capacity jack would be fine. Having a jack that…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 10

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 11

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 12

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer with the…

view full answer...

Phoenix Electric Trailer Jack Mounting Bracket to the top of the Jack Dimensions

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching