Availability of Retaining Clips for Dexter 7-Inch Round Magnet

Question

Question:

I just need a retainer clip for the round style magnet 7inch

asked by: Leland

0

Expert Reply:

I spoke with my contact at Redline about the availability of the retaining clip for the Dexter 7-inch brake magnets. He said you can use the Magnet Retainer Clip, part # BP19-001, on the Dexter 7-inch round magnets. These retaining clips will work on both the 7-inch round and the 10-inch oval magnets.

expert reply by: Jeff D

0

Answer 1

The Trailer Brake Magnet Kit, #BP01-068, will fit both Dexter 7 x 1-1/4 inch and 10 x 1-1/2 inch electric drum brake assemblies. This round magnet is what is considered to be the old style and fits Dexter 10 x 1-1/2 inch assemblies made prior to mid…

view full answer...

Answer 2

The 7 inch Dexter Brake Assemblies like the part #23-48 do use clips to attach the magnets to the assemblies. I went and pulled one from our warehouse and found that in order to attach the magnet to the arm you would need to slide the magnet over the…

view full answer...

Answer 3

I spoke with my contact at Redline about the availability of the retaining clip for the Dexter 7-inch brake magnets. He said you can use the Magnet Retainer Clip, part #BP19-001 , on the Dexter 7-inch round magnets. These retaining clips will work on…

view full answer...

Answer 4

As long as all 4 tires have brakes installed, all 4 tires are supposed to lock when the pin is pulled. If only one axle has brakes, the 2 of the 4 tires should lock. There are a couple of possible problems your trailer may be experiencing. One…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...