Replacement Aluminum Fender Gusset Step for Trailstar Boat Trailer

Question

Question:

I have a brand new Trailstar TXXPG175PB boat trailer. While towing the boat home, I hit a traffic pylon and dented the triangle shaped stepping platform that is in front of the wheel fender. Do you know if this part can be purchased separately?

asked by: Craig D

0

Expert Reply:

The closest part we carry is the CE Smith Steel Step for Trailer Fender, part # CE19012. However, since you mentioned your boat is brand new, chances are you want the exact replacement.

I recommend reaching out to the trailer manufacturer or whoever you purchased the boat/trailer from to source the direct replacement. Parts like the aluminum fender or gusset step are considered part of the trailer body/frame and are very specific to the particular trailer, which is why we do not carry them.

expert reply by: Carla M

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Aluminum Fender Gusset Step for Trailstar Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching