Bolts for Draw-Tite Trailer Hitch # 24769 Will Not Fit in the Frame of a 2007 Dodge Caliper
Question:
I have a 2007 caliber and I order this hitch but bolts doesnt fit on the holes any suggestions?
asked by: Vik
Expert Reply:
Take a look at the 4 bolts that came with the hitch. Make sure that they are 5/8-11 x 4 bolts. You will need to measure the diameter of the bolts where the threads are.
If you look at the video I have linked, you will see that our installer has to clean out the holes to get the bolts to fit through the frame. The holes could have corrosion and road grime build up inside where you cannot see it and cleaning it out should allow the bolts to fit. It will be a tight fit even after the holes are cleaned out.
If it is a case where the holes in the hitch are not lining up with the holes in the frame, then what probably occurred is that the hitch flexed some in the shipping process. As long as there are no stress fractures or marks or paint flaking off where the hitch flexed, you can bend it back. Use an open step, bench vise, or any method that will allow you to apply controlled force to the hitch to bend it back.
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: bike rack
- Shop: Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Shop: Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: Hollywood Racks Trail Rider Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Video: Trailer Hitch Installation - 2010 Dodge Caliber
- Article: Trailer Hitch Receiver Sizes
- Q&A: Rack For 2021 Rad Power Bike Radwagon And RadPower Utility bikes
- Video: Hollywood Racks Sport Rider SE Bike Rack Review
- Q&A: Bike Rack Recommendations for a Carbon Fiber Frame Bike
- Shop: BOLT brand vehicle and hitch locks
- Shop: Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches
- Shop: BOLT Trailer Hitch Receiver Lock for 1-1/4" Hitches - Codes to Chrysler/Dodge/Jeep Key
- Search Results: hitch lock
- Search Results: hitch bike rack lock
- Search Results: locking hitch pin
- Video: BOLT Trailer Hitch Receiver Lock Review
- Q&A: Bike Rack that Fits a 1-1/4 Inch Hitch Receiver to Carry a 75 Pound E-Bike
- Q&A: Trailer Hitch Recommendation for a 2009 Dodge Caliber R/T
- Search Results: 1up
- Search Results: hollywood racks
- Search Results: kuat piston pro
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)