Can I Use Wiring Junction Box part # 3375601101 On A Boat Trailer

Question

Question:

Would this box be suitable for wet location, ie, boat trailer?

asked by: John

1

Helpful Expert Reply:

The Trailer Wiring Junction Box part # 3375601101 is not designed for a marine application unless you keep the junction box as far away from the the water as possible. If you mount the box on the tongue and it doesn't get backed into the water when launch the boat then you should be okay. There may be boxes out there made for marine applications but we do not carry them at this time.

expert reply by: Heather A

1

Answer 1

Those are the wires for the brake magnets. You will need to connect the black wire to the brake controller output wire on your trailer connector and you are correct the white wire will need to be grounded to a clean metal surface on the trailer. I…

view full answer...

Answer 2

You should not need any extra fuses. Trucks like the Dodge Ram 2500 are built for towing and should have enough power on those circuits. First I would wire the lights to the trailer and worry about the 6-Way last. I would wire the lights with the…

view full answer...

Answer 3

The correct replacement for Atwood 7" x 1-3/4" Hydraulic Drum Brakes is the Dexter Hydraulic Trailer Brake Kit part #23-398-399. If you are having trouble removing the old brakes, I recommend applying heat but you can cut the nuts off worst…

view full answer...

Answer 4

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 5

The red wire is the turn signal wire and will be run to the green wire of your harness if its the right turn signal side, and the black wire will run to the brown wire of your harness. The yellow wire from your harness will run to the left turn…

view full answer...

Answer 6

The Buyers Products Trailer Wiring Junction Box #3375601101 referenced in your question measures 6.5 inches long, 3.21 inches wide, and 2.5 inches tall when the cover is installed. The mounting holes at each end are spaced apart 7.38 inches on…

view full answer...

Answer 7

The size of the nuts that fit the posts of the Trailer Wiring Junction Box #3375601101 is M5-.8 pitch. This does not come with extra nuts.

view full answer...

Answer 8

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 9

The only difference in the Demco Channel Tongue Trailer Couplers #DM16080-95 and #DM15931-95 is going to be the bolt pattern. One will have the 5-Bolt hole pattern and the other is going to have 4-Bolt holes. I have included images below showing the…

view full answer...

Answer 10

The side plates of the B&W gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail of your 2004 Dodge 2500 8-foot bed. See the B&W video I included at the 7 min and 30 second mark. If your Firestone air bags like…

view full answer...

Answer 11

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 12

To charge your batteries on your 2015 Lance 1575 from your vehicle or solar power and that is compatible with lithium batteries, I recommend the The Manager30 Battery Management System with Lithium Profile Item #RED88FR and the Pollak…

view full answer...

Can I Use Wiring Junction Box part # 3375601101 On A Boat Trailer

Product Page this Question was Asked From

Continue Researching