Hole Spacing in Base of C.E. Smith Bolster Bracket # CE10052-32G

Question

Question:

What is the hole spacing in the base? Is it sufficient to mount the bracket to a 2inch x 5inch frame rail with U bolts 2 1/8? Thank you.

asked by: DAN B

0

Expert Reply:

According to my contact at C.E. Smith, the manufacturer of the Bolster Bracket you referenced, the center to center dimension of the two holes in the base of the bracket is 1-1/4 inches with a 5/8 inch space between the two holes.

Using U-bolts to mount the bracket would work just fine.

I have edited a photo for you that shows the dimensions.

expert reply by: Mike L

0

click to enlarge

Answer 1

Yes, you could use 2 inch by 4 inch bunks on the CE Smith Bolster Bracket #CE10052-32G.

view full answer...

Answer 2

If you look at the provided photo, you can see the bolt spacing of the CE Smith #CE10052-32G bolster bracket.

view full answer...

Answer 3

The span of the CE Smith Bolster Bracket #CE10052-32G that you referenced is right at 15 inches. If you check out the image I attached you will see that dimension as well as a few others.

view full answer...

Answer 4

I went out to the warehouse and pulled a CE Smith Bolster Bracket #CE10052-32G to measure it. The actual width, not the span, is approximately 2 inches. It is actually just a hair under 2 inches but each one could be slightly different because of the…

view full answer...

Answer 5

The height of the CE Smith Bolster Bracket for Pontoon Boat Trailers part #CE10052-32G from the base to the top of the "V" is 5" which you can see in the photo below.

view full answer...

Answer 6

I checked with CE Smith and they informed me that the larger holes on the bracket that connect to the bunks and the larger holes are .410 of an inch and the smaller holes are .313 of an inch. Check out the picture I attached for more dimensions.

view full answer...

Answer 7

The end to end span of the CE Smith Bolster Bracket #CE10052-32G for Pontoon Boat Trailers is 15.03 inches, which, according to CE Smith is the most important measurement when talking about pontoon trailer brackets. CE Smith cannot guarantee these…

view full answer...

Answer 8

There really is no specific bunk board size recommendation to use with the CE Smith Bolster Bracket #CE10052-32G. It really just boils down to what works best for your application. Attached is a photo that a customer sent in where it looks like they…

view full answer...

Answer 9

If the #CE10052-32G was going to get attached to a trailer cross member you would want to bolt it through the cross member since the bolt holes wouldn't line up properly with a u-bolt. Since the install holes go left to right on the bracket the…

view full answer...

Answer 10

The CE Smith Bolster and Swivel Bracket Assembly - Galvanized Steel - 9" - Qty 1 #CE10000G is designed to hold a boat on a trailer, so it isn't very different to have them on a boat lift. These will work well for the tritoon you referenced.…

view full answer...

Answer 11

The CE Smith Bolster Bracket for Pontoon Boat Trailers part #CE10052-32G does not have a specific pontoon tube size requirement. That said, the CE Smith V-Wing Bolster Bracket for Pontoon Boat Trailers part #CE26244G would likely be a better option…

view full answer...

Answer 12

The CE Smith Bolster Bracket #CE10052-32G that you referenced is designed for supporting a pontoon boat when on a trailer so it could work for your pontoon lift. It is made of galvanized steel which will resist corrosion. Most lift components are…

view full answer...

Hole Spacing in Base of C.E. Smith Bolster Bracket # CE10052-32G

Product Page this Question was Asked From

Continue Researching