Height of CE Smith Bolster Bracket for Pontoon Boat Trailers

Question

Question:

CE Bolster Bracket # CE10052-32G I have looked at all the dimensions listed and dont see any listing on over all height of the bracket from the bottom to the top of the V. Can you provide me with that information? Thank you

asked by: Jeffrey H

0

Expert Reply:

The height of the CE Smith Bolster Bracket for Pontoon Boat Trailers part # CE10052-32G from the base to the top of the "V" is 5" which you can see in the photo below.

expert reply by: Conner L

0

CE Smith Bolster Bracket Height
(click to enlarge)

Answer 1

I checked with CE Smith and they informed me that the larger holes on the bracket that connect to the bunks and the larger holes are .410 of an inch and the smaller holes are .313 of an inch. Check out the picture I attached for more dimensions.

view full answer...

Answer 2

The end to end span of the CE Smith Bolster Bracket #CE10052-32G for Pontoon Boat Trailers is 15.03 inches, which, according to CE Smith is the most important measurement when talking about pontoon trailer brackets. CE Smith cannot guarantee these…

view full answer...

Answer 3

According to my contact at C.E. Smith, the manufacturer of the Bolster Bracket you referenced, the center to center dimension of the two holes in the base of the bracket is 1-1/4 inches with a 5/8 inch space between the two holes. Using U-bolts to…

view full answer...

Answer 4

I went out to the warehouse and pulled a CE Smith Bolster Bracket #CE10052-32G to measure it. The actual width, not the span, is approximately 2 inches. It is actually just a hair under 2 inches but each one could be slightly different because of the…

view full answer...

Answer 5

Yes, you could use 2 inch by 4 inch bunks on the CE Smith Bolster Bracket #CE10052-32G.

view full answer...

Answer 6

If you look at the provided photo, you can see the bolt spacing of the CE Smith #CE10052-32G bolster bracket.

view full answer...

Answer 7

The span of the CE Smith Bolster Bracket #CE10052-32G that you referenced is right at 15 inches. If you check out the image I attached you will see that dimension as well as a few others.

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Height of CE Smith Bolster Bracket for Pontoon Boat Trailers

Product Page this Question was Asked From

Continue Researching