Replacement Tyson Bearing 1779

Question

Question:

What replaces a Tyson 1779 bearing

asked by: TERESA S

0

Expert Reply:

I do have an option for you however I was not able to find the measurements of the Tyson 1779 bearing you are referring to. We do carry the Replacement Trailer Hub Bearing part # 1779 which measures an inner diameter of 0.938". I recommend to measure your Tyson bearing to make sure it matches up, if it does you can use the replacement etrailer 1779 bearing. You will need the race part # 1729 which measures 2.240".

expert reply by: Heather A

0

Answer 1

It sounds like you have the older hub 22834 that is no longer in production that takes the outer bearing of part #1779 and inner bearing of part #2788. I was not able to find any other bearings that measure .093" inner diameter besides 1779…

view full answer...

Answer 2

Although the #22834 hub is an older, obsolete trailer hub, we do have the replacement parts you are looking for. From what I have found, this hub uses a #29031 grease seal. The replacement inner bearing is #2788 and the outer bearing is #1779. The…

view full answer...

Answer 3

For your 1779 outer and 2788 inner bearings you will want the following parts. Replacement Trailer Hub Bearing - 1779 item #1779 Replacement Trailer Hub Bearing - 2788 item #2788 The closest seal we have to a National 5970 is item #29031 which has an…

view full answer...

Answer 4

For a wheel that is 5 inches in width and 15 inches in diameter you would want tires that are size ST205/75-15. For the tire size ST225/75R15 you listed you would want a rim that is from 6-7 inches in width. I attached a department page that has all…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Replacement Tyson Bearing 1779

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching