BAKFlip Tonneau Cover That Fits 2019 Ram 3500 Long Bed with Companion Hitch

Question

Question:

I have a 2019 Ram 3500 crew cab dual wheels 8foot bed. Does this fit ? on Baks site it claims for older body style I have the new. I also run BandW 5th wheel hitch BWRVK3600 how much room is required for height clearance my hitch is only inches below bed rails

asked by: Ray S

0

Expert Reply:

The BAKFlip MX4 Hard Tonneau Cover # BAK48204 that you referenced is confirmed as a fit for your 2019 Ram 3500 long bed with a new body style. As long as the highest point on your B and W Companion hitch part # BWRVK3600 is lower than the height of the vertical lip of the bed rails it will fit easily under the BAKFlip.

expert reply by: Jameson C

0

Answer 1

You can get a sense for how much visibility you'll have on your 5th wheel hitch with a tonneau cover folded up near the cab by viewing the linked image. The BAKFlip MX4 Hard Tonneau Cover #BAK48204 that fits your 2018 Ram 3500 long bed will be…

view full answer...

Answer 2

Thank you for all of the great info! While you technically could have enough room to make turns with the B&W Companion #BWRVK3370 and the BAKFlip MX4 Hard Tonneau Cover #BAK48330, from what I could find out I think you're only going to have a…

view full answer...

Answer 3

Since your 2017 Ram 3500 has an 8' bed the BAKFlip MX4 Hard Tonneau Cover #BAK48204 will be a quad-fold. Trucks that have a bed over 6' long will be quad-fold while trucks that have a bed under 6' long will be a tri-fold. I've sent an…

view full answer...

Answer 4

The BAKFlip MX4 Hard Tonneau Cover #BAK48330 sits about 1-1/2" below the top of the bed rails on your 2022 Ford F-350 Super Duty short bed. Since this is really close to the height of your B&W Companion #BWRVK3370. Because of this I…

view full answer...

Answer 5

The BAKFlip MX4 Hard Tonneau Cover - Folding - Aluminum - Matte Finish, #BAK48330, is a quad-fold cover. I reached out to my contact at BAK industries and for your 2017 Ford F-250 Super Duty with 6-3/4 foot bed, the depth of all the folds together is…

view full answer...

Answer 6

According to BAKflip, when the #BAK48330 is folded up against the rear of the truck cab, it'll reach into the bed by about 9 inches. Since the cover sits against the back of the cab when folded up and reaches most of the way up to the roof, it…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A93VR is designed to fit the youru 2022 Ram 3500 with a 8' dually bed. The Cover #A37FR will only fit an 8' bed with single rear wheels. This is the only difference in these covers is…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...