What are the Dimensions of the Base on the Ultra-Fab Stackable Stabilizers

Question

Question:

What are the dimensions of the base? I plan to place them on blocks of wood to provide more stability on soft ground.

asked by: Mimi

0

Expert Reply:

I spoke with my contact at Ultra-Fab and she stated that the stackable stabilizers, # UF48-979004, have a base that measures approximately 6 by 6 inches. I made a picture that shows the base dimensions.

expert reply by: Michael H

0

click to enlarge

Answer 1

The base dimensions of the Ultra-Fab Stackable Stabilizers #UF48-979004 that you referenced measure 6" x 6" at the bottom. I have attached a picture to demonstrate this.

view full answer...

Answer 2

I went out to the warehouse and measured the round base that contacts the bottom of the trailer for Ultra-Fab Stackable Stabilizers, #UF48-979004. It measures 1-3/4 inches in diameter. I made a video with this information and a picture as well. In…

view full answer...

Answer 3

I went out to our warehouse and got the following dimensions for the Stabilizer Jacks #TJ01RT-HD in the stowed position. I have included an image below so you can see the points I measured from. The overall length is 12-3/8" long,…

view full answer...

Answer 4

Best option for you would be to have the Stabilizer Jacks #TJ01RT-HD welded to your trailer frame. That will give you the most secure attachment. A local welder to you should have no problem attaching these. Would probably be the easiest job of his…

view full answer...

Answer 5

I have attached a few photos for you with all the dimensions we have for the Ark Drop Down Corner RV Stabilizer Jacks part #AR34FR. That said, Ark is an Australian company so the measurements are in metric, millimeter to be specific so you may need…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 7

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 8

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured also.…

view full answer...

Answer 9

We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

What are the Dimensions of the Base on the Ultra-Fab Stackable Stabilizers

Product Page this Question was Asked From

Continue Researching