How To Replace the Air Filter On a Firestone Compressor System

Question

Question:

I received a flat filter housing with my compressor kit #2158 and two replacement filters how do you replace the filter the housing doesn't seem to come apart please help

asked by: Dennis D

1

Helpful Expert Reply:

In order to replace the air filter on the Firestone Air Command I Compressor System part # F2158 you will first want to un-thread the filter housing from the compressor. Once the filter housing is removed you can then pry the two sides open with a flat-head screwdriver or pick tool. Once the two sides of the filter housing are separated you can simply remove the old and then replace it with a new filter. The filter housing will snap back together and you can thread it back on the compressor.

expert reply by: Conner L

1

Larry

5/23/2020

What does housing look like of Firestone 9284 air compressor? Never serviced it.

Reply

Chris R.

5/26/2020

I linked the install manual for the Firestone compressor system that should give you a better idea as to where the filter housing is located on the assembly (along with what it actually looks like).

Helpful Links

https://www.firestoneip.com/rr-kit-install-manuals/wr17602158.pdf

Reply

Answer 1

It looks like you need a trailer coupler repair kit for your trailer coupler. If that is the case then I would love to help but unfortunately I cannot identify the correct replacement coupler repair kit for you based on the photo you have attached.…

view full answer...

Answer 2

I reached out to my contact at firestone to confirm a few things. If the compressor is running, it should be filling the bags. The compressor is either going to build air pressure, or not build pressure. So if it is running when the bags are full,…

view full answer...

Answer 3

The E/CN error on your remote indicates that communication was not established for 2 seconds. The first thing you should try is using the remote outside near the compressor. If you do not have the error then there is interference inside the vehicle…

view full answer...

Answer 4

The ECN error code of a Firestone wireless compressor setup means that the remote has lost communication with the compressor. This very well can be because the compressor is not powered on so the remote has nothing to connect to. I would try…

view full answer...

Answer 5

It sounds like there may be a wiring issue or blown fuse on your Firestone compressor system like the part #F2543. The compressor should only run when the vehicle ignition is on, and even then only if the tank needs air. Check to make sure there…

view full answer...

Answer 6

Your 2017 DRV Mobile Suites 40KSSB4 has a 12 gallon water heater tank. Unfortunately I can&#39;t get enough information for your system off the web. We don&#39;t carry any 12 gallon options, so I don&#39;t know what anode rod…

view full answer...

Answer 7

First take some soapy water and use that to spray on all the connection points to ensure that there is not a leak in the system. Then you will want to check the air filter that goes to the compressor to ensure that it is not clogged or damaged in…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 &quot;pucks&quot; in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that&#39;s going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

How To Replace the Air Filter On a Firestone Compressor System

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching