Can Different Brand Brakes Be Used On Front and Rear Axle

Question

Question:

Is it ok to have lippert self adjusting brakes on the front axle and dexter on the back axle?

asked by: Bruce B

0

Expert Reply:

Yes, you can absolutely use the Dexter Nev-R-Adjust Brake Kit # 23-468-469 on one axle and a different brand, like Lippert, on the other. You can even use manual adjusting brakes on one axle and self adjusting brakes on the other; this will not cause any issues as long as you use the same style on each individual axle.

I've attached a helpful installation video for you at the bottom of the page.

expert reply by: Carla M

0

Answer 1

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 2

The Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K #23-468-469 are not designed to be manually adjusted in the way you are describing. There isn't really a way to back off the adjustment because…

view full answer...

Answer 3

If the surface on the inside of the drum where the shoe pads make contact isn't smooth then a brake shop may be able to turn the drums. If that surface or the surface where the magnet makes contact (called the armature surface) is discolored then…

view full answer...

Answer 4

I went out to the warehouse and pulled a Trailer Brake Magnet for 10" Hubs #BP01-110 and took some measurements for you. The brake magnet lead wires are 16 gauge wires and they measure 18 1/2 inches long.

view full answer...

Answer 5

The wires on the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #K23-478-00 are 12 gauge wires. We recommend using 10 Gauge Wire #10-1-1 from the trailer 7-Way connector to the brakes though to help ensure enough power gets to them.

view full answer...

Answer 6

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 7

The Dexter Nev-R-Adjust Electric Trailer Brake Kit part #23-468-469 is our best option for a 3,500 lb trailer axle. They are self-adjusting, made in the USA, and come with a five year warranty. You can mix self-adjusting and manual adjusting braking…

view full answer...

Answer 8

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 9

Biggest difference is the Dexter assemblies part #23-468-469 are made in the US and have basically the best reputation for trailer brake assemblies. If you are looking for the nicest setup that would be the most reliable this would be the route I…

view full answer...

Answer 10

Are there any visible signs of wear on the magnets like exposed windings then that would indicate they need replacing. Magnets can go bad without showing visible signs of wear though. To see how to troubleshoot them check out the help article I…

view full answer...

Answer 11

Your brakes are definitely adjustable and that's exactly what you should try doing first. You also have found the correct components on the assemblies that control the adjustments when you mentioned the star wheels behind the slots of the…

view full answer...

Answer 12

While it is normal for trailer brakes to get hot from braking if yours are getting excessively hot and only on 3 of the 4 assemblies they are likely too tight and creating friction while driving. You can adjust the Brakes #23-26-27 that you have on…

view full answer...

Can Different Brand Brakes Be Used On Front and Rear Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching