Mounting Ultra Fab # UF35-946401 Under Bumper

Question

Question:

According to the description for this model, it looks like it will be ok to mount this receiver under the bumper. Is this true? I will have plenty of clearance.

asked by: Mike P

0

Expert Reply:

It is acceptable to mount the Ultra Fab # UF35-946401 underneath the bumper.

Make sure the 200 lb capacity of the receiver or the capacity of the bumper (whichever is lower) is not exceeded.

This receiver is meant to mount to a 4 inch Steel RV bumpers, and not to a car or truck. It is not intended to be used for towing purposes.

expert reply by: Mike L

0

Answer 1

The amount of actual cargo weight you can safely transport on a hitch cargo carrier installed in a bumper-mounted hitch is determined by the lowest-rated component. Those components consist of the RV's bumper, the hitch such as #UF35-946401…

view full answer...

Answer 2

We have the perfect solution but the Furrion Vision S W is not compatible with the pre wiring from Voyager. Instead the Voyager WiSight Wireless RV Backup Camera #ASA24YR is the way to go. This will allow you to use the already existing bracket to…

view full answer...

Answer 3

The Swagman Around the Spare Deluxe 2 Bike Rack for RV Bumpers #S80501 with two standard bikes is not too much weight for your Flagstaff Ultra Light 4 inch bumper. The rack weighs about 20 lbs and can carry two bikes up to 35 lbs each. I assume you…

view full answer...

Answer 4

For the 24x64 etrailer Cargo Carrier for RV Bumper, #e83YR I recommend using the Fulton Economy Spare Tire Carrier, #FETCLB0201 to mount your spare to hang under the cargo carrier.

view full answer...

Answer 5

Yes, what you see in the pictures for the Ultra-Fab 2" Motor Home Trailer Hitch Receiver #UF35-946401 is what will ship. There was a redesign of this product, some of the photos you are seeing in reviews may be of the previous model. We do…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Mounting Ultra Fab # UF35-946401 Under Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching