Propane Adapter Hose For 17 Blackstone Griddle

Question

Question:

Will this hose allow me to replace the small cylinder used on my 17” Blackstone griddle.

asked by: Ralph T

0

Expert Reply:

If your Blackstone griddle has a female disposable cylinder port connector on it (which it sounds like you do), then yes, you will be able to use the MB Sturgis Propane Adapter Hose # 100555-144-MBS to connect the griddle to a 20-lb or 30-lb propane cylinder.

If your griddle has a different connector on it, please send me a picture and I will help identify the correct adapter hose for you to use for connecting to your propane cylinder.

expert reply by: Erik B

0

Answer 1

The hose you purchased would be fine as long as the heater you're connecting it to doesn't already have a built-in regulator or if the manufacturer specified that the two regulators would be needed to get the pressure right. Looking…

view full answer...

Answer 2

For your Weber Performer Deluxe Grill the adapter hose you're needing to switch to a 5lb propane cylinder is the MB Sturgis Propane Adapter Hose for Small Appliance - Type 1 x Disposable Cylinder Port - 12' Item #100555-144-MBS

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Propane Adapter Hose For 17 Blackstone Griddle

Product Page this Question was Asked From

Continue Researching