Is # BP01-225 a Replacement for # BP01-180 Brake Magnet

Question

Question:

Can brake magnet BP01-225 replace the dexter 6K brake magnet BP01-180 on the Nev-R-Adjust assemblies

asked by: Greg

0

Expert Reply:

According to my contacts at Redneck Trailer Supply, the less expensive BP01-225 is indeed an acceptable replacement for the BP01-180 brake magnets on your 12x2 Dexter brake assembly.

expert reply by: Mike L

0

Answer 1

As you may have already found, 5200 lb, 6000 lb and 7000 lb axles can all use the same components including inner/outer bearings, hubs and brakes. Here are some other things they share in common: Dexter 5200 lb Regular Duty Axle - 0.180 inch tube…

view full answer...

Answer 2

The Replacement Trailer Brake Magnet for Dexter Electric Brake Assemblies part #BP01-225 is designed for a 7,000 lb trailer axle.

view full answer...

Answer 3

The replacement magnet, #BP01-225, fits several different brake assemblies. it fits Dexter 10 x 2-1/4 inch assemblies, Dexter 12 x 2 manual assemblies and 12 x 2 Nev-R-Adjust assemblies, 7K axles. For a brake magnet with a red wire we have #BP01-285.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...