Replacement Braking Assemblies for a Big Tex 50LA Utility Trailer

Question

Question:

i am looking for the electric brake assemblies for a 14, 7000# big tex 50LA trailer gross weight each axle is 3500# Thanks

asked by: Tom C

1

Helpful Expert Reply:

The best electric trailer brake assembly kit we have for your Big Tex 50LA Trailer is the Dexter Nev-R-Adjust Electric Trailer Brake Kit part # 23-468-469. These are self-adjusting braking assemblies which means you don't have to move the star wheel every so often to ensure even brake pad wear. They are one of the best options on the market. If you are looking to save some money then you can go with the Dexter Electric Trailer Brake Kit part # 23-26-27 which are still a great option but require manual adjustments. These options will both be a direct bolt-on fit for your trailer.

expert reply by: Conner L

1

Answer 1

In order to find the right bearings more information is required. The easiest way to find which bearings you need is to remove the hub and check for the numbers that should be stamped into the bearings. If you are unable to locate these numbers,…

view full answer...

Answer 2

For 3,500 lb axles we have the bearing kit part #BK2-100 which comes with the bearings, seal, races, and a tang washer.

view full answer...

Answer 3

The Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K #23-468-469 are not designed to be manually adjusted in the way you are describing. There isn't really a way to back off the adjustment…

view full answer...

Answer 4

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 5

The Trimax Puck Lock for Trailer Door Hasps #TMX96RR cannot be keyed alike. While disappointing I'm sure, there is another option to consider, which is to order a quantity of two of the Trimax Puck Locks for Trailer Door Hasps #TMX73FR. The…

view full answer...

Answer 6

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 7

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…

view full answer...

Answer 10

The 4-way on your trailer is what's known as a wishbone connector like part #A35W42B. Two of the wires are the running light circuit which is a little easier to install since you can run one down each side of the trailer. This way you don't…

view full answer...

Answer 11

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Replacement Braking Assemblies for a Big Tex 50LA Utility Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching