What Is the Weight Capacity Of a Dexter D100G Axle

Question

Question:

I have an old gooseneck trailer with tandem duals All the info on the tag - dexter p-15 Model slr D100G SN D 2369596 Im just tryin to figure out what the axles are rated for

asked by: Mitchell P

0

Expert Reply:

The spoke with Dexter and the code "D100G" tells me you have two 10,000 lb trailer axles. I have attached some parts you may need for the axle below.

Dexter Trailer Hub Drum Assembly (After July 2009) - part # 8-430-5UC3
Dexter Trailer Hub and Drum Assembly (Before July 2009) - part # K08-288-90
Dexter Electric Trailer Brake Kit (12-1/4" x 4") - part # 23-438-439
Dexter Hydraulic Drum Brake Kit (12-1/4" x 4") - part # 23-404-405

Inner Bearing - part # 387A
Inner Race - part # 382A
Outer Bearing - part # 25580
Outer Race - part # 25520
Oil Seal Kit - part # RG04-300

expert reply by: Conner L

0

Answer 1

Thank you for the picture! I reached out to my contact at Dexter and your axle is indeed a 10000lb axle, but with the axles age they were unable to confirm the oil seal or bearings used. With that said your axle being a general duty 10000lb axle…

view full answer...

Answer 2

The P-15 model information you provided for your Dexter axle does indicate its model, but you will still need to note its length and capacity before locating the correct replacement. If you are able to find a longer serial number somewhere on the…

view full answer...

Answer 3

Is there a capacity listed anywhere on the axle? I can give Dexter the serial number of your axle but it may take a couple days and if you could get me the diameter of your axles or the capacity I could much quicker get you what you need.

view full answer...

Answer 4

I spoke with my rep at Dexter axle and was informed your axle has a 3,500 lbs weight capacity, with a 58" spring center, and a 72" hub face. A comparable replacement is the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72"…

view full answer...

Answer 5

Actually all you really have to do is remove the oil from the hub and then pack the hubs with grease and then get the correct bearing buddy to match the threaded hub bore. You will need to measure the inner diameter of where the old grease cap…

view full answer...

Answer 6

It looks like you're likely trying to replace your hubs/drums on your Dexter axle and I do believe that the "0100" you found on the spec plate actually reads "D100" since that was one of the models that Dexter had for this…

view full answer...

Answer 7

In order to remove the hub/drum on your trailer you will want to first remove the spindle nut. Once the spindle nut is removed you are going to want to take a hammer and tap the outer portion of the drum as well as the hub face a few times to break…

view full answer...

Answer 8

The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Say…

view full answer...

Answer 9

The best system we have for your situation would be a disc brake kit with an electric over hydraulic actuator, like the Cargo Towing Solutions HydraStar Electric-Hydraulic Actuator w/ Line Kit for Disc Brakes, #CAR-HBA16-2. To install this system you…

view full answer...

Answer 10

If your axle was produced after April 2001 there should be a lot number on the axle. Go to the rear side of the axle beam about 18 inches from the curb side of the vehicle (passenger side). If you see "DEXTER AXLE" the lot number should be…

view full answer...

Answer 11

I called Dexter and they told me that your Dexter P-12 SLR SN: D5287869 axle has a 3,000 lb weight capacity. If you need any parts please let me know what they are and I would be happy to offer my recommendation.

view full answer...

Answer 12

Sure, you can weld the low-profile Titan Chain Lashing Winch for Flatbed Truck or Trailer #TCLR860 to the bottom of your flatbed truck. The only difference between this winch and the "bottom mount" Titan Chain Lashing Winch for Flatbed…

view full answer...

What Is the Weight Capacity Of a Dexter D100G Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching