Width of Rhino-Rack Accessory Bars # RR43120B

Question

Question:

Hi, what’s the width of the accessory bar? Thanks

asked by: Kimo

1

Helpful Expert Reply:

The Rhino-Rack Accessory Bars # RR43120B that you referenced have a width of exactly 2.36 inches. They also have a height of 0.9 inch.

I have attached the written installation instructions for the bars below that you might also find helpful.

expert reply by: Chris R

1

Answer 1

Yes, the Rhino Rack Pioneer Platform Accessory bars part #RR43120B that you referenced will allow you to install the Yakima SkyBox 12 part #Y07334 that you are interested in! I attached a picture that shows a cargo box attached to these bars for…

view full answer...

Answer 2

We do indeed have the Rhino-Rack nuts you are looking for, in a quantity of 8; what you need is the following: - Quick Mount Nuts for Rhino-Rack RTL600 Legs - Factory Tracks - Qty 8 #RRQMFK11-2

view full answer...

Answer 3

Here are the 2 different mounting options for installing the Batwing and Foxwing Awning Relocation Kit #RR31102. You can change the orientation of the brackets so that the awning will either hang higher or lower depending on your application.

view full answer...

Answer 4

For your 2017 Mercedes-Benz Sprinter 2500 with the factory rails I recommend the Rhino-Rack Heavy-Duty Roof Rack Crossbars #RB1800B-2 with Rhino-Rack Quick Mount Legs #RRRLT600, Quick Mount Nuts #RRQMFK11-2 and Roof Rack Leg Spacer Blocks…

view full answer...

Answer 5

Based on the part number you gave me, it looks like you are needing Quick Mount Nuts for Rhino-Rack RTL600 Legs - Factory Tracks - Qty 4 #RRQMFK11. These are made to fit the Rhino-Rack RTL600 Legs into Rhino-Rack roof tracks such as the Rhino-Rack…

view full answer...

Answer 6

I reached out to Rhino Rack on your behalf about your situation. The confirmed that the backbone system #RR57AT does not fit your vehicle. I do have tracks that will work for you though. These tracks #RRRTV208 are 81 inches long and have about 26…

view full answer...

Answer 7

I reached out to my contact at Rhino-Rack and there are no adapters or spacers required to use the Rhino-Rack Track Mount RLTP Legs for Factory Roof Rack Tracks - 2" Tall - Qty 2 #RLTPMV with the Pioneer platform. They said instead you may…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 12

Easiest solution for that would be the Curt auxiliary LED indicator lights part #C53201. This would allow you to add stoplight/turn signals to your bike rack and it plugs into a 4-way like you mentioned.

view full answer...

Width of Rhino-Rack Accessory Bars # RR43120B

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching