Replacement End Cap for Load Bar on Thule Xsporter Ladder Rack

Question

Question:

What is the part # for the loadbar end cap screw

asked by: Alvino G

0

Expert Reply:

The load bar end carp replacement for the Thule Xsporter Pro is part # 852-3214001 on our site. This comes in a quantity of 1.

expert reply by: Jon G

0

Alvino G.

8/21/2019

What is the part # for the loadbar end cap screw

Reply

Jon G.

8/21/2019

The replacement screw to secure the end cap # 852-3214001 is part # THHD-27059.

Reply

Answer 1

The correct replacement end cap for Thule's Xsporter Pro Adjustable-Height Truck Bed Ladder Rack #TH500XT is part #852-3214001. I confirmed this item's fit with my contact at Thule.

view full answer...

Answer 2

The Replacement Base Assembly Cap for Thule Xsporter Pro Adjustable Height Truck Bed Ladder - Qty 1 #8523168001 is the bottom part you are pointing to. They are the same on the top and bottom.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Replacement End Cap for Load Bar on Thule Xsporter Ladder Rack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching