Distance from Center Hitch Pin Hole to Anti-Rattle Pin Fastway DTSTBM7000-2S

Question

Question:

What is the measurement from the center of the 5/8inch receiver pin to the outer edge of the tensioning anti-rattle pin? I want to make sure that the tensioning anti-rattle pin fits entirely inside of the shaft of my hitch. Thank you

asked by: Jon

1

Helpful Expert Reply:

The distance from the center of the hitch pin hole to the furthest away edge of the anti-rattle pin that extends out of the top of the ball mount's shank is right at 2-1/8 inches, as you can see in the photo I've edited for you.

expert reply by: Mike L

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

I checked with B&W and their Trailer Hitch Receiver Lock for 3" Hitches item #BW23FR doesn't have a maximum capacity listed because it is rated for a shear strength much higher than the capacity of any 3" receiver and ball mount on…

view full answer...

Answer 5

The air bag kit I recommend going with to fit the Adaptive Ride Control on your 2022 GMC Sierra 1500 Limited is the Firestone Ride-Rite Air Helper Springs #F2609. Even though there are a limited amount of air bags that fit your vehicle, the Firestone…

view full answer...

Answer 6

Hey Sylvia, the diameter of the lock core side of the B and W Coupler Lock part #BW23FR is 1 inch.

view full answer...

Answer 7

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 8

The Firestone Ride-Rite Air Helper Springs #F2609 is the only kit that we have that will fit your 2020 GMC Sierra 1500 Denali with the adaptive ride control. These have a 5,000lb capacity to enhance your factory suspension under load. This will not…

view full answer...

Answer 9

The reason why you would need the #VGR74VR filter to use the #ASA37YR is because your 2022 GMC Sierra 1500 will have pulse width modulation (PWM). This means it won't send consistent power back to the camera and you're going to lose the…

view full answer...

Answer 10

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 11

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 12

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...