What Is the Max Amperage Allowed for the Hopkins Endurance Easy-Pull Harness HM38136

Question

Question:

What is the max amperage and wattage allowed on this harness??

asked by: John

0

Expert Reply:

The Hopkins Endurance Easy-Pull Harness part # HM38136 uses 18 gauge wire for all but the ground circuit and it comes with a 25' long lead therefore it will max out at around 5 amps or 60 watts.

expert reply by: Conner L

0

Answer 1

Yes. The M421KR is a Petersen part and the Optronics equivalent is the Sealed, 6-1/2 inch Oval Trailer Stop, Turn and Tail Light, 3-Function, #ST70RB, that you have referenced. For a complete set up, you will need Rubber Grommet #A70GB, and Straight…

view full answer...

Answer 2

Connecting the brown running light wire in standard 4-pole wiring to both tail lights will require a jumper wire from one side of the trailer to the other, or you can install what's called a wishbone harness that has dual brown running light…

view full answer...

Answer 3

The wire gauge of the Sealed, 3-Light Truck, Trailer Identification LED Light Bar #MCL93RB that you referenced is 16 gauge.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...